WeatherMaster Ice & Water 200

WeatherMaster Ice and Water 200 Roof Underlayment

WeatherMaster^® Ice & Water is a composite roof underlayment designed to provide a secondary waterproofing barrier needed to prevent ice dams and damage from wind-blown rain.

A proprietary fiberglass mat reinforced, SBS-modified asphalt makes WeatherMaster^® Ice & Water ideally suited for continuous waterproofing protection against ice dams and wind-blown rain year after year. The self-adhesive underlayment creates a watertight barrier by sealing to the roof deck and around nails. WeatherMaster^® Ice & Water provides excellent traction and protection from UV degradation and weathering thanks to its granular surface.

Benefits of WeatherMaster^® Ice & Water
Roof Underlayment

UV Protected Surface – 45 Day Exposure
High Temperature Stability – 240°F
Self-Adhesive Backing Seals Directly to the Deck
55 Mil Thickness, 38% Above Industry Requirement
Dual Modified Asphalt Provides Superior Granule Adhesion
Aggressive Bond at Low Temperatures, 45°F Min.
SBS-Modified Asphalt Coating Helps Seal Around Nails for a Watertight Result
Fiberglass Mat Is Stronger and Provides Better Tear Resistance Than Saturated Felt Underlayment
Atlas Signature Select^® Roofing System Eligible

WeatherMaster^® Ice & Water provides a homeowner with an extra layer of waterproofing protection and peace of mind when the weather gets rough.

Technical & Installation Details

See It Now

Where To Buy

Get It Installed

Click Here

Features
Technical Information

Atlas Signature Select Roofing System Eligible

For maximum protection and warranty coverage, install an Atlas Signature Select® Roofing System with components designed and backed by an Atlas Warrant.

Atlas Signature Select Roofing System Drawing

1Atlas WeatherMaster®
Ice & Water Underlayment

2Atlas Premium
Underlayment

3Atlas Pro-Cut®
Starter Shingles

4Atlas Roof Shingles

5Atlas Pro-Cut®
Hip & Ridge Shingles

Learn More

Codes & Compliances

Length: 65’
Width : 36"
Square Per Roll: 1.95

ASTM

Meets ASTM D-1970

UL

UL Classified as a Prepared Roofing Accessory
Florida Building Code Approved - FL 17322
UL Class A and Class C Fire Rating
Miami-Dade County Product Control Approved, Miami-Dade County, Florida

Safety

Learn and observe safe roofing practices according to OSHA and local building code requirements. Always use caution when walking on sloped roof decks and WeatherMaster^® Ice & Water underlayment. Do not walk on unsecured WeatherMaster^® Ice & Water or any other loose material lying on sloped roof decks. Dust, dew, water and debris create unsafe conditions on the roof. The presence of any foreign matter may drastically change the coefficient of friction (traction) on WeatherMaster^® Ice & Water or any other material on a sloped roof deck. Failure to always use proper safety equipment and footwear can result in serious injury or even death.

Installation Instructions:

WeatherMaster Ice & Water 100 & 200 Installation Instructions

WeatherMaster^® Ice & Water Installation Instructions

Installation For Roof Decks (Rakes and Eaves)

To begin, remove any dust, dirt, loose nails or other protrusions from the roof deck. Remove all shingles, roofing felt and nails from the deck of existing roofs. Sweep thoroughly to remove any dust and dirt. Apply WeatherMaster^® underlayment only in fair weather when air surface temperatures are above 45°F and rising. Apply to dry surfaces only.

Apply sheet parallel to the roof edge, extending over 1/4". Overlap edge seams 3", so that laps will shed water. End seams should be overlapped 6" and staggered. On steep slope applications it may be necessary to spot nail the top edge of the membrane temporarily during the installation process. For wrinkle-free application, cut WeatherMaster^® underlayment into 10 to 15 foot lengths and reroll in reverse direction.

Peel back 1 to 2 feet of release paper. Align the sheet on the lower edge of the roof and adhere the first 1 to 2 feet. Pull the release paper from under the sheet and continue to peel it while pressing the sheet into place. Roll lower edges firmly with a wallpaper roller or other hand roller. For ice dam protection, WeatherMaster^® underlayment must be applied to reach a point above the highest expected level of ice dams (minimum application at least to a height of 24" beyond the interior wall line). End laps should be overlapped 6" and staggered. When installing at temperatures below 45°F and on slopes above 8" in 12"—face nail in the overlap area at the top of the sheet at 12" OC. Priming the deck may be necessary below 45°F.

For Valleys and Ridges

Cut WeatherMaster^® underlayment into 4 to 6 foot lengths. Peel the release paper and center sheet over valley or ridge. Drape and press sheet into place, working from the center of the valley or ridge in each direction. For valleys, apply the sheet starting at the lowest point and work upward. WeatherMaster^® underlayment should not be left permanently exposed to the weather. It must be covered by shingles, metal valley flashing or other roofing materials within 30 days. Overlap horizontal overlaps at least 6" in valleys.

Smooth shank galvanized nails are recommended for fastening shingles. Do not overdrive nails or break the surface.

WeatherMaster® Ice & Water 200 Related Documents:

WeatherMaster Ice & Water 100 200 216 Data Sheet

PDF

257.28kb

WeatherMaster® Ice & Water 200

Benefits of WeatherMaster® Ice & Water Roof Underlayment